SC4510ITSTRT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | SC4510 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Qualification Status | Not Qualified |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 16V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 4.75V~16V |
| Control Features | Enable, Frequency Control, Power Good, Soft Start |
| Input Voltage (Min) | 4.75V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 100kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Duty Cycle | 90 % |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SC4510ITSTRT Overview
With a 20-TSSOP (0.173, 4.40mm Width) package, the switching controller is suitable for a wide range of applications. 1 outputs can be generated with the dc motor controller. There is a Tape & Reel (TR) solid enclosure around the pmic. Transistor Driver dc switching's outputs (s) are supported. 4.75V~16V is the supply voltage and the operating voltage of the dc control. Qualified to work in an dc switcher with -40°C~85°C TA. There is a switch at 100kHz~1MHz that can be used with this controller. As it has a Surface Mount value, it can be used for general dc dc regulator. In order to control switching efficiently, the dcdc regulator features Enable, Frequency Control, Power Good, Soft Start. Switch converters are connected to ICs with SWITCHING CONTROLLER analog outputs. There are a terminal (s) on the switching converters that are designed at DUAL. A variety of 20 terminations are available in dc switching. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. DC switcher's input voltageis set to 12V. SC4510 can be used to locate other relevant dc to dc converter ics. There are a total of 20 pins on switching converter. In particular, switching converter is a type of Switching Regulator or Controllers. 4.75V should be the minimum input voltage for the dc dc voltage regulator. If you start a project, note down the dc dc regulator's usual output current of 1A. A duty cycle set at 90 % ensures voltage regulator dc to dc reliability during power-on and power-off. This Surface Mount makes DC switcher suitable for most prototypes and applications. It is suggested that users apply 16V to the voltage regulator dc to dc in order to run it safely and reliably in a circuit.
SC4510ITSTRT Features
Transistor Driver Outputs
Switching Frequency: 100kHz~1MHz
Enable, Frequency Control, Power Good, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 90 %
SC4510ITSTRT Applications
There are a lot of Semtech Corporation SC4510ITSTRT DC to DC converter applications.
- Thermal power
- Automation technology
- Overvoltage protection circuits in TV sets
- Grinders
- Production lines
- Energy management systems
- SMT equipment
- Linear guide
- Imported equipment
- Electrical power transmission
