SG1845Y-883B
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-CDIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Series | Military, MIL-STD-883B |
| JESD-609 Code | e0 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Pitch | 2.54mm |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 30V |
| Input Voltage-Nom | 15V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 7.6V~30V |
| Topology | Flyback |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 1Hz~500kHz |
| Input Voltage (Max) | 25V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 50ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 50 ns |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 50 % |
| Duty Cycle (Max) | 48% |
| Clock Sync | No |
| Length | 9.905mm |
| Width | 7.62mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
SG1845Y-883B Overview
It comes in a 8-CDIP (0.300, 7.62mm) package, so switching controller can be used for most applications. There is enough capacity in the dc motor controller to generate the output for the 1 input. PMIC packaging is solid with a Tube enclosure. Transistor Driver dc switching's outputs (s) can be handled by it. A 7.6V~30V voltage is supplied to the dc control and used for operating it. Workable in an dc switcher where -55°C~125°C TA is the -55°C~125°C TArm. It can switch at 1Hz~500kHz. The Through Hole value makes it suitable for general dc dc regulator. An analog IC SWITCHING CONTROLLER is connected to the switch converters. Switching converters are designed with the terminal (s) at position DUAL . A variety of 8 terminations are available in dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 15V is input. Total pins of switching converter are 8. In particular, switching converter is a type of Switching Regulator or Controllers. A maximum voltage of 25V is accepted by the dc to dc regulator as an input voltage. If you are starting a new project, you should note the dc dc regulator's typical output current is 200mA. voltage regulator dc to dcs with a 50 % duty cycle are designed to be reliable when powered on and powered off. In most applications and prototype designs, DC switcher is qualified as a Through Hole. To run the voltage regulator dc to dc safely and reliably, users should apply 30V to the voltage regulator dc to dc. It belongs to the dc to dc voltage regulator series Military, MIL-STD-883B.
SG1845Y-883B Features
Transistor Driver Outputs
Switching Frequency: 1Hz~500kHz
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
SG1845Y-883B Applications
There are a lot of Microchip Technology SG1845Y-883B DC to DC converter applications.
- Current source circuits
- Ball screw pair
- Radio equipment
- Sink circuits
- Hydrogen power
- Imported equipment
- Medical equipment
- Household control circuits
- Surge protection circuits
- Computer monitoring equipment of building
