SG2524N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 951.693491mg |
| Operating Temperature | -25°C~85°C TA |
| Packaging | Tube |
| Tolerance | 4% |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | Through Hole |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Frequency | 722kHz |
| Base Part Number | SG2524 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 5V |
| Output Type | Transistor Driver |
| Max Output Current | 50mA |
| Input Voltage-Nom | 20V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 8V~40V |
| Quiescent Current | 8mA |
| Control Features | Current Limit, Frequency Control |
| Max Output Voltage | 5.2V |
| Input Voltage (Min) | 8V |
| Topology | Buck, Boost, Flyback, Forward Converter, Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 450kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Reference Voltage | 5V |
| Rise Time | 200ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 100 ns |
| Max Duty Cycle | 45 % |
| Output Phases | 1 |
| Height | 5.08mm |
| Length | 19.3mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SG2524N Overview
In the 16-DIP (0.300, 7.62mm) package, the switching controller meets most application requirements. 2 outputs are supported by the dc motor controller. A solid enclosure of Tube surrounds pmic. It is capable of handling Transistor Driver dc switching's outputs (s). DC control operates at 8V~40V volts and has 8V~40V supply voltage. A -25°C~85°C TA dc switcher is not a problem. It can switch at 450kHz. Through Hole makes it suitable for general dc dc regulator. For efficient switching control, the dcdc regulator features Current Limit, Frequency Control. An analog IC SWITCHING CONTROLLER is connected to the switch converters. Thare switching converters has a terminal (s) at DUAL . An array of 16 terminations of dc switching. To name a few of the control techniques these dc dc converter ics adapt, it includes PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 20V. You can find other relevant dc to dc converter ics by searching "SG2524". 16 pins are present on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. 8V should be the minimum input voltage for the dc dc voltage regulator. The test statistics indicate that DC regulator outputs a voltage of 5V. In most cases, the output current of the dc dc regulator will be 100mA, so note that when you start the project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 45 %. Switching controllers operate at 722kHz frequencies. DC switching uses 8mA when it is dormant. An output current greater than 50mA cannot be provided by the dc switcher. The datasheet indicates that the switching converter can output 5.2V volts at its maximum.
SG2524N Features
Transistor Driver Outputs
Switching Frequency: 450kHz
Current Limit, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
Frequency: 722kHz
SG2524N Applications
There are a lot of Texas Instruments SG2524N DC to DC converter applications.
- Post equipment
- Planers
- Computer rooms
- Window air conditioners
- Medical equipment
- Adjustable voltage or current linear circuits
- seismic instrument power circuits
- Various CNC machine tools
- Computer monitoring equipment of building
- Nuclear power plants
