SG3524P013TR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 200.686274mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Frequency | 400kHz |
| Base Part Number | SG3524 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 18V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 20V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 8V~40V |
| Quiescent Current | 8mA |
| Control Features | Enable |
| Input Voltage (Min) | 8V |
| Topology | Flyback, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 300kHz |
| Input Voltage (Max) | 40V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 200ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 100 ns |
| Max Duty Cycle | 45 % |
| Output Phases | 1 |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SG3524P013TR Overview
Capsuled in the 16-SOIC (0.154, 3.90mm Width) package, the switching controller can be used for a wide range of applications. For 2 outputs, the dc motor controller is appropriate. Cut Tape (CT) is the solid enclosure in which PMIC is packaged. A total of Transistor Driver dc switching's outputs can be handled by it. dc controls with 8V~40V voltage are supplied and operated. Worked in a 0°C~70°C TA dc switcher before. With this switching controller, you can switch at 300kHz. Surface Mount makes it suitable for general dc dc regulator. Enable provides dcdc regulator efficient switching control. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. The switching converters's terminals (s) are designed at DUAL. A variety of terminations with 16 of dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. 20V nominal DC switcher's voltage input. Other relevant dc to dc converter ics will be returned if you search "SG3524". There are only 16 pins on switching converter. Switching converter is a special type of Switching Regulator or Controllers. This dc dc voltage regulator should be powered by a voltage of 8V. DC regulator outputs 18V voltage based on test statistics. It should be fully noted that the dc to dc regulator only accepts 40V input voltage at most. normally, the dc dc regulator's output current is 100mA, which you should keep in mind when starting a project. A duty cycle set at 45 % ensures voltage regulator dc to dc reliability during power-on and power-off. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. A frequency of 400kHz is used by the switching controller. Dormant dc switchings use 8mA.
SG3524P013TR Features
Transistor Driver Outputs
Switching Frequency: 300kHz
Enable
PULSE WIDTH MODULATION
Max Duty Cycle: 45 %
Frequency: 400kHz
SG3524P013TR Applications
There are a lot of STMicroelectronics SG3524P013TR DC to DC converter applications.
- Serial communication converter
- Series voltage regulation circuits
- Radio equipment
- Industrial controllers
- Imported equipment
- Driver circuits
- Product burn-in
- Automation technology
- Direct power supply system
- Emergency lighting monitoring equipment
