SG3525ADWG
| Parameters | |
|---|---|
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | SG3525A |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 20V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 400mA |
| Voltage - Supply (Vcc/Vdd) | 8V~35V |
| Max Supply Current | 20mA |
| Control Features | Enable, Frequency Control, Soft Start |
| Input Voltage (Min) | 8V |
| Topology | Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100Hz~400kHz |
| Input Voltage (Max) | 35V |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 100ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 50 ns |
| Max Frequency | 400kHz |
| Max Duty Cycle | 49 % |
| Output Phases | 1 |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SG3525ADWG Overview
With its 16-SOIC (0.295, 7.50mm Width) package, the switching controller fits the needs of most applications. It is sufficient to generate 2 outputs with this dc motor controller. The pmic is packaged in Tube solid enclosure. Transistor Driver dc switching's outputs (s) are supported. 8V~35V is the operating voltage and supply voltage of the dc control. Work well in dc switchers with a 0°C~70°C TA. It can switch at 100Hz~400kHz. It is suitable for general dc dc regulator when it is set to Surface Mount. The dcdc regulator features Enable, Frequency Control, Soft Start for efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. Terminal (s) of the switching converters are designed at the DUAL position. A variety of terminations with 16 of dc switching. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. 20V nominal DC switcher's voltage input. Other relevant dc to dc converter ics can be found by searching "SG3525A". The switching converter has a total of 16 pins. Specifically, switching converter falls under the Switching Regulator or Controllers category. Input voltage of dc dc voltage regulator should be 8V. It should be fully noted that the dc to dc regulator only accepts 35V input voltage at most. It's important to remember that the dc dc regulator's normaloutput current is 400mA, so you should note it down when starting a new project. Voltage regulator dc to dc is designed to operate at 49 % duty cycle during power-ups and power-downs to ensure reliability. DC switcher's Surface Mount makes it qualified for most application and prototype designs. DC switcher'sDC regulators have a maximum frequency of 400kHz. Components may be damaged if their current is greater than 20mA.
SG3525ADWG Features
Transistor Driver Outputs
Switching Frequency: 100Hz~400kHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 49 %
SG3525ADWG Applications
There are a lot of ON Semiconductor SG3525ADWG DC to DC converter applications.
- CMM
- Emergency lighting monitoring equipment
- Servo drive system
- Electric heating, lighting
- Radio equipment
- Analog precision reference circuits
- Bending machines
- Surge protection circuits
- Packaging
- Scientific research
