SG3525ANG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 16 hours ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Frequency | 400kHz |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | SG3525A |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Output Voltage | 18V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 20V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 8V~35V |
| Control Features | Enable, Frequency Control, Soft Start |
| Input Voltage (Min) | 8V |
| Topology | Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 100Hz~400kHz |
| Input Voltage (Max) | 35V |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Duty Cycle (Max) | 49% |
| Output Phases | 1 |
| Height Seated (Max) | 4.44mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SG3525ANG Overview
It comes in a 16-DIP (0.300, 7.62mm) package, so switching controller can be used for most applications. The dc motor controller is adquate to generate for 2 outputs. A solid enclosure of Tube surrounds pmic. A total of Transistor Driver dc switching's outputs can be handled by it. DC control operates at 8V~35V volts and has 8V~35V supply voltage. Worked in an dc switcher with a 0°C~70°C TA rating. The switching controller can be switched at 100Hz~400kHz. As it has a Through Hole value, it can be used for general dc dc regulator. Enable, Frequency Control, Soft Start provides dcdc regulator efficient switching control. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. Switching converters are designed with the terminal (s) at position DUAL . Different dc switching's functions can be applied to 16 terminations. PULSE WIDTH MODULATION is an example of one of the control techniques these dc dc converter ics adapt. 20V nominal DC switcher's voltage input. SG3525A can be searched for other relevant dc to dc converter ics. 16 pins are on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. dc dc voltage regulators should have a minimum input voltage of 8V. DC regulator outputs 18V voltage based on test statistics. Voltages 35V are the maximum that the dc to dc regulator will accept. If you start a project, note down the dc dc regulator's usual output current of 100mA. A frequency of 400kHz is set for the switching controller.
SG3525ANG Features
Transistor Driver Outputs
Switching Frequency: 100Hz~400kHz
Enable, Frequency Control, Soft Start
PULSE WIDTH MODULATION
Frequency: 400kHz
SG3525ANG Applications
There are a lot of ON Semiconductor SG3525ANG DC to DC converter applications.
- Wind power
- Hydro power
- Solar power plants
- Plate bending machines
- Refrigerators of central air conditioners
- Drilling machines
- USB circuits
- Correction machines
- Game consoles
- Balance equipment
