SI9110DY-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 338.011364mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BCDMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | SI9110 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 9.7V |
| Output Type | Transistor Driver |
| Max Output Current | 150μA |
| Input Voltage-Nom | 48V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 10mA |
| Voltage - Supply (Vcc/Vdd) | 9.5V~13.5V |
| Control Features | Enable, Reset |
| Topology | Cuk, Flyback, Forward Converter, Push-Pull |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 40kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 40ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 40 ns |
| Switcher Configuration | SINGLE |
| Max Frequency | 3MHz |
| Max Duty Cycle | 50 % |
| Duty Cycle | 50 % |
| Length | 8.65mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SI9110DY-E3 Overview
Capsuled in the 14-SOIC (0.154, 3.90mm Width) package, the switching controller can be used for a wide range of applications. For outputs of 1, this dc motor controller is suitable. A solid enclosure of Tape & Reel (TR) surrounds pmic. The program can handle Transistor Driver dc switching's outputs (s). This dc control has a supply voltage and operating voltage of 9.5V~13.5V. Qualified to work in a -40°C~85°C TA dc switcher. It can switch at 40kHz~1MHz. The Surface Mount allows it to be used for dc dc regulator in general. Switching control is made easier with the dcdc regulator's Enable, Reset. Thare switch converters are connected to an analog integrated circuit (IC) of type SWITCHING CONTROLLER. DUAL are the position of the terminal of the switching converters. 14 terminations with various dc switching's functions. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. DC switcher's input voltageis set to 48V. In addition to "SI9110", there are other relevant dc to dc converter ics you can find. There are 14 pins on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. A 9.7V voltage of DC regulator was detected in the test statistics. It's important to remember that the dc dc regulator's normaloutput current is 10mA, so you should note it down when starting a new project. voltage regulator dc to dcs with a 50 % duty cycle are designed to be reliable when powered on and powered off. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. There is a maximum frequency of 3MHz for this dc regulators. A dc switcher can only produce an output current of 150μA.
SI9110DY-E3 Features
Transistor Driver Outputs
Switching Frequency: 40kHz~1MHz
Enable, Reset
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
SI9110DY-E3 Applications
There are a lot of Vishay Siliconix SI9110DY-E3 DC to DC converter applications.
- Linear guide
- Refrigerators of central air conditioners
- Emergency lighting monitoring equipment
- Various precision measuring instruments
- Wide-range voltage regulation circuits
- Textile machinery
- Smoke exhaust equipment
- Pipe bending machines
- Analog precision reference circuits
- Planers
