SM73308MG/NOPB
| Parameters | |
|---|---|
| Number of Elements | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 600μA |
| Slew Rate | 1.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.23pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V |
| Output Current per Channel | 75mA |
| Input Offset Voltage (Vos) | 250μV |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 100dB |
| Power Supply Rejection Ratio (PSRR) | 82dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 3.5MHz |
| Max I/O Voltage | 850μV |
| Wideband | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 23 hours ago) |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | SolarMagic™ |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | SM73308 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
SM73308MG/NOPB Overview
A 5-TSSOP, SC-70-5, SOT-353 case is used to package the op amp. Buffer amps of this type are called General Purpose-types. A Tape & Reel (TR) case is used for delivering the op amp. The number of terminations is approaching the 5 mark. Buffer amplifier has a total of 5 pins. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. This particular linear amplifier is a type of Operational Amplifier device, to be precise. The op amp ic has an array of 5 pins on it. Op amp ic rates 250μV for input offset voltage. This electrical part should be mounted using type Surface Mount. It is important to note that this linear amplifier works well at a temperature of -40°C~125°C when it comes to operating temperatureIn order for this instrumentation amplifier to operate, the supply current needs to be between 600μA and 10 . You should keep the voltage gain at 100dB for the time being. A linear amplifier like this has 1 circuits on it. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. Depending on the chip's operating supply voltage, op amp ic has a rated voltage of 1. To pack the operational amplifier ics, TR is adopted as the packing method. In this case, SolarMagic? represents the instrumentation amplifiers' series number.
SM73308MG/NOPB Features
5 Pins
supply voltage of 5V
100dB voltage gain
Output Type: Rail-to-Rail
SM73308MG/NOPB Applications
There are a lot of Texas Instruments SM73308MG/NOPB Instrumentational OP Amps applications.
- Fast A/D and D/A converters
- Signal operation
- Video conversion and routing
- Power generator
- Scintillation detectors
- Automatic control
- Test equipment
- Proportional operation circuits
- Band-stop filter
- Active probe
