Parameters |
Base Part Number |
65C1167 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
5V |
Power Supplies |
5V |
Operating Supply Current |
200mA |
Nominal Supply Current |
9mA |
Logic Function |
Receiver, Transceiver |
Data Rate |
10 Mbps |
Output Characteristics |
3-STATE |
Differential Output |
YES |
Output Polarity |
TRUE |
Protocol |
RS422, RS485 |
Input Characteristics |
DIFFERENTIAL SCHMITT TRIGGER |
Number of Drivers/Receivers |
2/2 |
Receiver Number of Bits |
2 |
Duplex |
Full |
Receiver Hysteresis |
60mV |
Number of Drivers |
2 |
Number of Transceivers |
1 |
Supply Voltage1-Nom |
5V |
Out Swing-Min |
2 V |
Height |
2mm |
Length |
10.3mm |
Width |
5.3mm |
Thickness |
1.95mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 6 days ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.209, 5.30mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Weight |
200.686274mg |
Operating Temperature |
-40°C~85°C |
Packaging |
Cut Tape (CT) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Type |
Transceiver |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Additional Feature |
RECEIVER 3-STATE OUTPUTS |
Subcategory |
Line Driver or Receivers |
Technology |
BICMOS |
Voltage - Supply |
4.5V~5.5V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
SN65C1167NSR Overview
LED drivers with the enhanced 16-SOIC (0.209, 5.30mm Width) package will be able to drive a variety of common LEDs with ease.Cut Tape (CT) package is used to mount this receiver.Several solutions have used this Transceiver can transceiver in a variety of applications due to its Transceiver IC nature.You can place this wide receiver to any Surface Mount-type PCB or development board.A power supply of 4.5V~5.5V is used by this differential driver.It is possible to have up to 2/2 receivers/drivers in use simultaneously with this electronic part.As its name implies, this ic receiver is designed for applications where -40°C~85°C is the operating temperature.Driver ICs in this category can operate efficiently with a supply voltage range of 5V.In this wide receiver, 16 terminations are integrated for driving and receiving signals from data.As a standard package, this transceiver comes with a 16-pin layout that follows the market standard.As the base part number 65C1167 identifies the product type, temperature, package, etc., you can try searching with it to get more variants of this part.The driver IC has improved power dissipation control.This receiver is typically specified with a resolution of 2 bits. There is a voltage input supply of 5V required for the operation of this integrated circuit.This rf transceiver module can be grouped into a subcategory named Line Driver or Receivers.An 8-pin power supply is provided by this driver IC, which allows it to operate from an 5V-pin power supply.This IC implements 1 transceivers overall.On the part, 2 drivers are embedded in order to facilitate the operation of the device.In addition, the optical transceiver module incorporates a RECEIVER 3-STATE OUTPUTS function that improves the overall stability and accuracy of the signal management.Using a 200mA input voltage, this integrating circuit is capable of driving LEDs with an output voltage of 20 V.
SN65C1167NSR Features
Cut Tape (CT) package
16 pin count
16 pins
5V power supply
SN65C1167NSR Applications
There are a lot of Texas Instruments SN65C1167NSR Drivers/Receivers/Transceivers applications.
- Aircraft positioning
- Carrier phase observations
- SONET/SDH Network
- Single to Multimode Fiber Conversion
- Fiber-to-the-desktop
- Transmission stations
- Fiber distributed data interface (FDDI)
- WDM transmission
- Wireless showroom
- Clock radio