SN65LVDT2DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 13.012431mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | 65LVDT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Type | Receiver |
| Technology | TTL |
| Voltage - Supply | 2.4V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | 65LVDT2 |
| Pin Count | 5 |
| Operating Supply Voltage | 3.3V |
| Operating Supply Current | 7mA |
| Nominal Supply Current | 8mA |
| Power Dissipation | 385mW |
| Propagation Delay | 3.1 ns |
| Turn On Delay Time | 3.1 ns |
| Max Output Voltage | 454mV |
| Data Rate | 400Mbps |
| Differential Output | NO |
| Protocol | LVDS |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 0/1 |
| Driver Number of Bits | 1 |
| Max Input Current | 20μA |
| Interface Standard | EIA-644-A; TIA-644-A |
| Receive Delay-Max | 3.6 ns |
| Supply Voltage1-Nom | 3.3V |
| Output Low Current-Max | 0.008A |
| Number of Receivers | 1 |
| Out Swing-Min | 2 V |
| High Level Input Current-Max | 0.00002A |
| Ambient Temperature Range High | 85°C |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN65LVDT2DBVR Overview
LED drivers benefit from this IC's enhanced SC-74A, SOT-753 package.In the Cut Tape (CT) package, this receiver is mounted.Since this is a Receiver can transceiver, many solutions can use it for a variety of functions.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.With respect to the power supply, this differential driver uses 2.4V~3.6V.There can be up to 0/1 eligible receivers/drivers on the field at the same time with this electronic part.This ic receiver has been primarily designed for applications where the operating temperature is -40°C~85°C.Wide receiver can operate within the range of 3.3V supply voltages efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.The pinouts for this transceiver are standardized to meet the needs of the market.Since the base part number 65LVDT2 uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.The driver IC has improved power dissipation control.Its package size is drastically reduced by downsizing ICs and utilizing high-density Surface Mount mounting techniques.An important feature of this ic receiver was its 1-bit resolution capability.An input voltage supply of 3.3V is required to operate the transceiver module.There are also 1 receivers in it as well.It is capable of driving LEDs with a voltage of 7mA as the input voltage to this integrating circuit.One of the 65LVDT series, representing an enhanced power-saving method, is this integrating circuit.
SN65LVDT2DBVR Features
Cut Tape (CT) package
5 pin count
5 pins
65LVDT series
SN65LVDT2DBVR Applications
There are a lot of Texas Instruments SN65LVDT2DBVR Drivers/Receivers/Transceivers applications.
- Bridges
- Desktop PC
- Data center
- Remote controls
- Automation systems
- Aircraft positioning
- Clock radio
- Wireless projection application for conferences
- TV signal transmission
- Metro access rings
