SN65MLVD206D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | Transceiver |
| Subcategory | Line Driver or Receivers |
| Max Power Dissipation | 725mW |
| Technology | CMOS |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Base Part Number | 65MLVD206 |
| Pin Count | 8 |
| Operating Supply Voltage | 3.3V |
| Operating Supply Current | 24mA |
| Nominal Supply Current | 24mA |
| Power Dissipation | 725mW |
| Propagation Delay | 6 ns |
| Turn On Delay Time | 6 ns |
| Data Rate | 200Mbps |
| Output Characteristics | DIFFERENTIAL |
| Differential Output | YES |
| Output Polarity | COMPLEMENTARY |
| Protocol | LVDS, Multipoint |
| Input Characteristics | DIFFERENTIAL SCHMITT TRIGGER |
| Number of Drivers/Receivers | 1/1 |
| Driver Number of Bits | 1 |
| Max Input Current | 10μA |
| Duplex | Half |
| Receiver Hysteresis | 25mV |
| Transmit Delay-Max | 2.4 ns |
| Supply Voltage1-Nom | 3.3V |
| Number of Receivers | 1 |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN65MLVD206D Overview
LED drivers with the enhanced 8-SOIC (0.154, 3.90mm Width) package will be able to drive a variety of common LEDs with ease.The Tube package houses this receiver.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.On any Surface Mount-type PCB or development board, this wide receiver can be placed.Power supply requirements for this differential driver are 3V~3.6V.During operation, this electronic part may have up to 1/1 eligible receivers/drivers.This ic receiver has been primarily designed for applications where the operating temperature is -40°C~85°C.There is a voltage range of 3.3V for this line driver ic, so it can operate efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.The transceiver is packaged with 8 market standard pinouts so that it can be easily used.This part number 65MLVD206 can be used to search for more variants based on the product type, temperature, package, etc.8-pin driver chip with enhanced power dissipation.In this ic receiver, the resolution was able to be set to a maximum of 1 bits.There is a voltage input supply of 3.3V required for the operation of this integrated circuit.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.The module isolated transceivers are 1 receivers.With an input voltage of 24mA, this integrating circuit has the ability to drive LEDs with an output voltage of 24mA.
SN65MLVD206D Features
Tube package
8 pin count
8 pins
SN65MLVD206D Applications
There are a lot of Texas Instruments SN65MLVD206D Drivers/Receivers/Transceivers applications.
- Aircraft positioning
- Wireless network systems
- Notebook
- IP cameras
- Metro access rings
- Single fiber bidirectional application
- Low power, low voltage systems
- VoIP phones
- Structural bonding
- Servers
