SN74ABT162823ADLR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 56-BSSOP (0.295, 7.50mm Width) |
| Number of Pins | 56 |
| Weight | 694.790113mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 56 |
| Type | D-Type |
| Additional Feature | WITH CLEAR AND CLOCK ENABLE |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Supply Voltage | 5V |
| Base Part Number | 74ABT162823 |
| Function | Master Reset |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 12mA |
| Number of Bits | 9 |
| Clock Frequency | 150MHz |
| Propagation Delay | 6.2 ns |
| Turn On Delay Time | 2.3 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 500μA |
| Current - Output High, Low | 12mA 12mA |
| Max Propagation Delay @ V, Max CL | 6.2ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 7.5 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Power Supply Current-Max (ICC) | 80mA |
| Number of Input Lines | 9 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 150000000Hz |
| Length | 18.415mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT162823ADLR Overview
The flip flop is packaged in a case of 56-BSSOP (0.295, 7.50mm Width). You can find it in the Cut Tape (CT)package. As configured, the output uses Tri-State, Non-Inverted. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. Temperature is set to -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 74ABT series. In order for it to function properly, its output frequency should not exceed 150MHz. In total, it contains 2 elements. There is 500μA quiescent consumption. 56terminations have occurred. The 74ABT162823 family contains this object. A voltage of 5V is used to power it. This JK flip flop has a 3.5pFfarad input capacitance. It is a member of the ABTfamily of D flip flop. The electronic part is mounted in the way of Surface Mount. As you can see from the design, it has pins with 56. This device exhibits a clock edge trigger type of Positive Edge. It is part of the FF/Latchesbase part number family. This flip flop is designed with 9 Bits. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. An electrical current of 5V volts is applied to it. The D flip flop is embedded with 2ports. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. The output current of 12mA makes it feature maximum design flexibility. It has 3 output lines to operate. There are 9 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. In addition, you can refer to the additinal WITH CLEAR AND CLOCK ENABLE of the D latch.
SN74ABT162823ADLR Features
Cut Tape (CT) package
74ABT series
56 pins
9 Bits
5V power supplies
SN74ABT162823ADLR Applications
There are a lot of Texas Instruments SN74ABT162823ADLR Flip Flops applications.
- Shift Registers
- Set-reset capability
- Clock pulse
- Computing
- Instrumentation
- Single Up Count-Control Line
- QML qualified product
- Registers
- ESD protection
- Dynamic threshold performance
