SN74ABT273DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ABT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 6.8 ns |
| Quiescent Current | 30mA |
| Turn On Delay Time | 2.5 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 400μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 7.3 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT273DBR Overview
In the form of 20-SSOP (0.209, 5.30mm Width), it has been packaged. It is contained within the Cut Tape (CT)package. It is configured with Non-Invertedas an output. It is configured with the trigger Positive Edge. There is an electronic component mounted in the way of Surface Mount. A voltage of 4.5V~5.5Vis required for its operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. It belongs to the type D-Typeof flip flops. The 74ABTseries comprises this type of FPGA. You should not exceed 150MHzin its output frequency. In total, there are 1 elements. T flip flop consumes 400μA quiescent energy. The number of terminations is 20. It is a member of the 74ABT273 family. A voltage of 5V is used as the power supply for this D latch. A JK flip flop with a 7pFfarad input capacitance is used here. This D flip flop belongs to the family of ABT. It is mounted by the way of Surface Mount. 20pins are included in its design. This device exhibits a clock edge trigger type of Positive Edge. This RS flip flops is a part number FF/Latches. This flip flop is designed with 8 Bits. Its flexibility is enhanced by 8 circuits. As a result of its reliable performance, this T flip flop is suitable for TR. A total of 5V power supplies are needed to run it. High efficiency requires the supply voltage to be maintained at 5V. It consumes a total of 30mA quiescent current at any given time.
SN74ABT273DBR Features
Cut Tape (CT) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT273DBR Applications
There are a lot of Texas Instruments SN74ABT273DBR Flip Flops applications.
- Convert a momentary switch to a toggle switch
- ESD protection
- Power down protection
- Communications
- Data storage
- Buffered Clock
- Guaranteed simultaneous switching noise level
- Event Detectors
- Control circuits
- Frequency Dividers
