SN74ABT273DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ABT273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 150MHz |
| Propagation Delay | 6.8 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 400μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.8ns @ 5V, 50pF |
| Prop. Delay@Nom-Sup | 7.3 ns |
| Trigger Type | Positive Edge |
| Input Capacitance | 7pF |
| Power Supply Current-Max (ICC) | 30mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT273DWR Overview
It is packaged in the way of 20-SOIC (0.295, 7.50mm Width). D flip flop is embedded in the Cut Tape (CT) package. As configured, the output uses Non-Inverted. This trigger uses the value Positive Edge. There is an electric part mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. A temperature of -40°C~85°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. FPGAs belonging to the 74ABTseries contain this type of chip. In order for it to function properly, its output frequency should not exceed 150MHz. A total of 1elements are present in it. It consumes 400μA of quiescent current without being affected by external factors. 20terminations have occurred. If you search by 74ABT273, you will find similar parts. Power is provided by a 5V supply. A JK flip flop with a 7pFfarad input capacitance is used here. It is a member of the ABTfamily of D flip flop. There is an electronic component mounted in the way of Surface Mount. It is designed with 20 pins. A Positive Edgeclock edge trigger is used in this device. The part is included in FF/Latches. An electronic part with 8bits has been designed. Due to its superior flexibility, it uses 8 circuits. Considering its reliability, this T flip flop is well suited for TR. An electrical current of 5V volts is applied to it. High efficiency requires the supply voltage to be maintained at 5V. Featuring the maximum design flexibility, it has an output current of 64mA .
SN74ABT273DWR Features
Cut Tape (CT) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT273DWR Applications
There are a lot of Texas Instruments SN74ABT273DWR Flip Flops applications.
- Divide a clock signal by 2 or 4
- Data transfer
- Bus hold
- Frequency Dividers
- ATE
- Communications
- Safety Clamp
- Load Control
- ESD protection
- Count Modes
