SN74ABT374APWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ABT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 7.1 ns |
| Quiescent Current | 30mA |
| Turn On Delay Time | 4.2 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT374APWR Overview
20-TSSOP (0.173, 4.40mm Width)is the packaging method. D flip flop is embedded in the Cut Tape (CT) package. T flip flop uses Tri-State, Non-Invertedas its output configuration. This trigger is configured to use Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. The operating temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. It belongs to the 74ABTseries of FPGAs. There should be no greater frequency than 200MHzon its output. The list contains 1 elements. T flip flop consumes 250μA quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The object belongs to the 74ABT374 family. A voltage of 5V is used as the power supply for this D latch. Its input capacitance is 3.5pF farads. An electronic device belonging to the family ABTcan be found here. It is mounted in the way of Surface Mount. This board is designed with 20pins on it. This device exhibits a clock edge trigger type of Positive Edge. This RS flip flops is a part number FF/Latches. The flip flop is designed with 8bits. 8 circuits are used to achieve its superior flexibility. As a result of its reliability, this D flip flop is ideally suited for TR. It runs on 5Vvolts of power. The flip flop contains 2ports. It is recommended that the supply voltage be kept at 5Vto maximize efficiency. With an output current of 64mA, it is possible to design the device in any way you want. It has 3 output lines to operate. 30mAquiescent current consumed.
SN74ABT374APWR Features
Cut Tape (CT) package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT374APWR Applications
There are a lot of Texas Instruments SN74ABT374APWR Flip Flops applications.
- Data storage
- Functionally equivalent to the MC10/100EL29
- Computing
- Clock pulse
- Instrumentation
- Data transfer
- Safety Clamp
- Bus hold
- Event Detectors
- Power down protection
