SN74ABT377ADWG4
| Parameters | |
|---|---|
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Current - Output | 64mA |
| Propagation Delay | 6.8 ns |
| Turn On Delay Time | 4.5 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -32mA |
| Low Level Output Current | 64mA |
| Power Supply Current-Max (ICC) | 30mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | WITH HOLD MODE |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 150MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
SN74ABT377ADWG4 Overview
SOICis the packaging method. Currently, the output is configured to use TTL. A total of 1elements are present in it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. Power is supplied from a voltage of 5V volts. Devices in the ABTfamily are electronic devices. The electronic part is mounted in the way of Surface Mount. This board has 20 pins. This device's clock edge trigger type is Positive Edge. This part is included in FF/Latches. In view of its reliability, this D flip flop is a good fit for TUBE. The D latch runs on a voltage of 5V volts. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. There is also a characteristic of WITH HOLD MODE. High level output current is set to -32mA. A 64mAvalue is set for low-level output current. A temperature below 85°Cis recommended for operation. A temperature above -40°Cshould be used for the operation. It is powered by 4.5V as its minimum supply voltage. 5.5Vis the maximum supply voltage supported by it. This frequency can be achieved 150MHz. It uses a logic IC with a D FLIP-FLOP value. Currently, it is equipped with 1 functions . 20pins are available on this JK flip flop. As a result of its output current of 64mA, it is very flexible in terms of design.
SN74ABT377ADWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74ABT377ADWG4 Applications
There are a lot of Texas Instruments SN74ABT377ADWG4 Flip Flops applications.
- Modulo – n – counter
- Common Clocks
- Memory
- Frequency division
- Test & Measurement
- Clock pulse
- Control circuits
- ESCC
- Power down protection
- 2 – Bit synchronous counter
