SN74ABT574ADWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 374 |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 200MHz |
| Pin Count | 20 |
| Output Type | TTL |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Number of Ports | 2 |
| Current - Output | 64mA |
| Propagation Delay | 6.6 ns |
| Turn On Delay Time | 3.9 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.064 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -32mA |
| Low Level Output Current | 64mA |
| Power Supply Current-Max (ICC) | 30mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74ABT574ADWRG4 Overview
The package is in the form of SOIC. TTLis the output configured for it. D latch consists of 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The power source is powered by 5V. It is a member of the ABTfamily of D flip flop. It is mounted by the way of Surface Mount. There are 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This RS flip flops is a part number FF/Latches. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. It operates from 5V power supplies. There are 2 ports embedded in the flip flops. In order to achieve high efficiency, the supply voltage should be maintained at 5V. There is also a characteristic of BROADSIDE VERSION OF 374. High level output current is set to -32mA. It is set to 64mAfor the low level output current. A temperature below 85°Cshould be used for operation. Ideally, the operating temperature should be higher than -40°C. Initially, it requires a voltage of 4.5V as the minimum supply voltage. 5.5Vis the maximum supply voltage it supports. A frequency of 200MHzcan be achieved. It adopts a logic IC of type BUS DRIVER. It is equipped with 1 Functions . 20pins are available on this JK flip flop. As a result of its output current of 64mA, it is very flexible in terms of design.
SN74ABT574ADWRG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74ABT574ADWRG4 Applications
There are a lot of Texas Instruments SN74ABT574ADWRG4 Flip Flops applications.
- Memory
- Differential Individual
- Computers
- Storage registers
- Frequency division
- Pattern generators
- Count Modes
- Data storage
- Data Synchronizers
- Buffer registers
