SN74ABT574APW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ABT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | BICMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ABT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 64mA |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 6.6 ns |
| Turn On Delay Time | 3.9 ns |
| Family | ABT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 250μA |
| Current - Output High, Low | 32mA 64mA |
| Max I(ol) | 0.064 A |
| Max Propagation Delay @ V, Max CL | 6.6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3.5pF |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ABT574APW Overview
It is packaged in the way of 20-TSSOP (0.173, 4.40mm Width). It is included in the package Tube. This output is configured with Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. The electronic part is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. It is operating at a temperature of -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. It belongs to the 74ABTseries of FPGAs. In order for it to function properly, its output frequency should not exceed 200MHz. In total, there are 1 elements. During its operation, it consumes 250μA quiescent energy. A total of 20terminations have been recorded. You can search similar parts based on 74ABT574. A voltage of 5V is used as the power supply for this D latch. This T flip flop has a capacitance of 3.5pF farads at the input. It is a member of the ABTfamily of D flip flop. It is mounted in the way of Surface Mount. Basically, it is designed with a set of 20 pins. This device exhibits a clock edge trigger type of Positive Edge. The RS flip flops belongs to FF/Latches base part number. It is designed with a number of bits of 8. Using 8 circuits, it is highly flexible. A total of 5V power supplies are needed to run it. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. With an output current of 64mA, it is possible to design the device in any way you want. There are 3 output lines in this JK flip flop.
SN74ABT574APW Features
Tube package
74ABT series
20 pins
8 Bits
5V power supplies
SN74ABT574APW Applications
There are a lot of Texas Instruments SN74ABT574APW Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Counters
- Load Control
- Common Clocks
- Storage Registers
- Digital electronics systems
- Memory
- Single Down Count-Control Line
- ATE
- Buffered Clock
