SN74AC374DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 155MHz |
| Propagation Delay | 13.5 ns |
| Turn On Delay Time | 8 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Output Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 60000000Hz |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC374DBR Overview
20-SSOP (0.209, 5.30mm Width)is the way it is packaged. There is an embedded version in the package Cut Tape (CT). The output it is configured with uses Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. Surface Mountis in the way of this electric part. The JK flip flop operates at a voltage of 2V~6V. It is operating at -40°C~85°C TA. D-Typeis the type of this D latch. This type of FPGA is a part of the 74AC series. It should not exceed 155MHzin terms of its output frequency. The element count is 1 . It consumes 4μA of quiescent current without being affected by external factors. The number of terminations is 20. The 74AC374 family contains it. The D flip flop is powered by a voltage of 3.3V . The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the ACfamily of D flip flop. Surface Mount mounts this electronic component. 20pins are included in its design. There is a clock edge trigger type of Positive Edgeon this device. The part you are looking for is included in FF/Latches. The design is based on 8bits. As soon as 6Vis reached, Vsup reaches its maximum value. Normally, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this circuit is achieved by using 8 circuits. In view of its reliability, this D flip flop is a good fit for TR. A D flip flop with 2embedded ports is available. It offers maximum design flexibility with its output current of 24mA. There are 3 output lines on it.
SN74AC374DBR Features
Cut Tape (CT) package
74AC series
20 pins
8 Bits
SN74AC374DBR Applications
There are a lot of Texas Instruments SN74AC374DBR Flip Flops applications.
- Digital electronics systems
- Guaranteed simultaneous switching noise level
- Frequency Dividers
- Event Detectors
- Registers
- Storage registers
- Common Clocks
- QML qualified product
- Set-reset capability
- Buffer registers
