SN74AC374DWE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Frequency | 155MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 13.5 ns |
| Turn On Delay Time | 8 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AC374DWE4 Overview
In the form of SOIC, it has been packaged. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The D flip flop is powered by a voltage of 3.3V . Electronic devices of this type belong to the ACfamily. This electronic part is mounted in the way of Surface Mount. 20pins are included in its design. This device has the clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. There are 8bits in this flip flop. Its superior flexibility is attributed to its use of 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TUBE. The flip flop has 2embedded ports. It has 1 output lines to operate. There are 3 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. The high level output current is set to -24mA. 24mAis set as the low level output current. The operating temperature should be lower than 85°C. The operating temperature should be higher than -40°C. Initially, it requires a voltage of 2V as the minimum supply voltage. It is capable of supporting a maximum supply voltage of 6V. This frequency can be achieved at 155MHz. BUS DRIVERis used as the logic IC in this D flip flop. The T flip flop is equipped with 1functions . It is equipped with 20 pin count. Its output current of 24mA allows for maximum design flexibility.
SN74AC374DWE4 Features
20 pins
8 Bits
1 Functions
20 pin count
SN74AC374DWE4 Applications
There are a lot of Texas Instruments SN74AC374DWE4 Flip Flops applications.
- Individual Asynchronous Resets
- Storage Registers
- Memory
- Safety Clamp
- CMOS Process
- Pattern generators
- Parallel data storage
- High Performance Logic for test systems
- ESD performance
- Frequency Dividers
