SN74AC374DWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 155MHz |
| Propagation Delay | 15.5 ns |
| Turn On Delay Time | 8 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 8ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 60000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC374DWR Overview
It is embeded in 20-SOIC (0.295, 7.50mm Width) case. A package named Cut Tape (CT)includes it. Tri-State, Non-Invertedis the output configured for it. JK flip flop uses Positive Edgeas the trigger. This electronic part is mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. A temperature of -40°C~85°C TAis used in the operation. This logic flip flop is classified as type D-Type. It belongs to the 74ACseries of FPGAs. Its output frequency should not exceed 155MHz. D latch consists of 1 elements. There is 4μA quiescent consumption. 20terminations have occurred. JK flip flop belongs to 74AC374 family. A voltage of 3.3V is used to power it. Its input capacitance is 4.5pF farads. It belongs to the family of electronic devices known as AC. This electronic part is mounted in the way of Surface Mount. This board is designed with 20pins on it. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. The design is based on 8bits. 6Vis the maximum supply voltage (Vsup). For normal operation, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this circuit is achieved by using 8 circuits. As a result of its reliability, this D flip flop is ideally suited for TR. A total of 2ports are embedded in the D flip flop. With an output current of 24mA, it is possible to design the device in any way you want. Currently, there are 3 input lines present.
SN74AC374DWR Features
Cut Tape (CT) package
74AC series
20 pins
8 Bits
SN74AC374DWR Applications
There are a lot of Texas Instruments SN74AC374DWR Flip Flops applications.
- Instrumentation
- Bus hold
- Communications
- Convert a momentary switch to a toggle switch
- Counters
- Differential Individual
- Shift registers
- CMOS Process
- Buffer registers
- Test & Measurement
