SN74AC564N
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Weight | 1.1991g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Supply Voltage | 3.3V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74AC564 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Number of Elements | 1 |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 95MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 4.9 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 5.08mm |
| Length | 24.33mm |
| Width | 6.35mm |
| Thickness | 4.57mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC564N Overview
20-DIP (0.300, 7.62mm)is the way it is packaged. D flip flop is included in the Tubepackage. As configured, the output uses Tri-State, Inverted. There is a trigger configured with Positive Edge. This electronic part is mounted in the way of Through Hole. The JK flip flop operates with an input voltage of 2V~6V volts. It is operating at a temperature of -40°C~85°C TA. It is an electronic flip flop with the type D-Type. It is a type of FPGA belonging to the 74AC series. It should not exceed 95MHzin its output frequency. D latch consists of 1 elements. As a result, it consumes 4μA quiescent current and is not affected by external forces. A total of 20terminations have been recorded. The 74AC564family includes it. The D flip flop is powered by a voltage of 3.3V . The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the ACfamily are electronic devices. This electronic part is mounted in the way of Through Hole. This board has 20 pins. A Positive Edgeclock edge trigger is used in this device. It is included in FF/Latches. 8bits are used in its design. Vsup reaches its maximum value at 6V. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. The superior flexibility of this product is achieved by using 8 circuits. There are 2 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. Featuring the maximum design flexibility, it has an output current of 24mA . As of now, there are 3input lines.
SN74AC564N Features
Tube package
74AC series
20 pins
8 Bits
SN74AC564N Applications
There are a lot of Texas Instruments SN74AC564N Flip Flops applications.
- Event Detectors
- Single Down Count-Control Line
- 2 – Bit synchronous counter
- Patented noise
- Latch
- Asynchronous counter
- Instrumentation
- Balanced 24 mA output drivers
- Functionally equivalent to the MC10/100EL29
- Convert a momentary switch to a toggle switch
