SN74AC574PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AC574 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 153MHz |
| Propagation Delay | 15 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 9.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 60000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC574PW Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). The package Tubecontains it. Currently, the output is configured to use Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. There is an electronic component mounted in the way of Surface Mount. A 2V~6Vsupply voltage is required for it to operate. It is operating at a temperature of -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. The 74ACseries comprises this type of FPGA. In order for it to function properly, its output frequency should not exceed 153MHz. In total, it contains 1 elements. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is a member of the 74AC574 family. An input voltage of 3.3Vpowers the D latch. This JK flip flop has a 4.5pFfarad input capacitance. Devices in the ACfamily are electronic devices. Electronic part Surface Mountis mounted in the way. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. It is part of the FF/Latchesbase part number family. There are 8bits in its design. Vsup reaches 6V, the maximal supply voltage. For normal operation, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this circuit is achieved by using 8 circuits. There are 2 ports embedded in the flip flops. This T flip flop features a maximum design flexibility due to its output current of 24mA. This input has 3lines in it. It consumes 4μA current.
SN74AC574PW Features
Tube package
74AC series
20 pins
8 Bits
SN74AC574PW Applications
There are a lot of Texas Instruments SN74AC574PW Flip Flops applications.
- Instrumentation
- Memory
- Event Detectors
- Bus hold
- Count Modes
- ATE
- Frequency division
- Balanced Propagation Delays
- Frequency Dividers
- Cold spare funcion
