SN74AC74DR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 122.413241mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 160MHz |
| Propagation Delay | 16 ns |
| Quiescent Current | 2μA |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 6ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC74DR Overview
The package is in the form of 14-SOIC (0.154, 3.90mm Width). As part of the package Cut Tape (CT), it is embedded. Differentialis the output configured for it. It is configured with a trigger that uses Positive Edge. The electronic part is mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. In this case, the operating temperature is -40°C~85°C TA. The type of this D latch is D-Type. The 74ACseries comprises this type of FPGA. It should not exceed 160MHzin terms of its output frequency. It has been determined that there have been 14 terminations. This D latch belongs to the family of 74AC74. The power source is powered by 3V. There is 3pF input capacitance for this T flip flop. In terms of electronic devices, this device belongs to the ACfamily of devices. The electronic part is mounted in the way of Surface Mount. There are 14pins on it. There is a clock edge trigger type of Positive Edgeon this device. The RS flip flops belongs to FF/Latches base part number. In this case, the maximum supply voltage (Vsup) reaches 6V. Normal operation requires a supply voltage (Vsup) above 2V. Its superior flexibility is attributed to its use of 2 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. An electrical current of 3.3/5V volts is applied to it. With an output current of 24mA, it is possible to design the device in any way you want. As of now, there are 4input lines. Quiescent current is consumed by the D latch in the amount of 2μA.
SN74AC74DR Features
Cut Tape (CT) package
74AC series
14 pins
3.3/5V power supplies
SN74AC74DR Applications
There are a lot of Texas Instruments SN74AC74DR Flip Flops applications.
- Balanced 24 mA output drivers
- EMI reduction circuitry
- Frequency Divider circuits
- Latch-up performance
- Computers
- Frequency Dividers
- Shift Registers
- Circuit Design
- CMOS Process
- Instrumentation
