SN74AC74PWRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 160MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | AND, D-Type |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AC74PWRG4 Overview
The flip flop is packaged in a case of 14-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). T flip flop uses Differentialas the output. This trigger uses the value Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at 2V~6Vvolts. The operating temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. JK flip flop belongs to the 74ACseries of FPGAs. In order for it to function properly, its output frequency should not exceed 160MHz. It consumes 2μA of quiescent There are 14 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The object belongs to the 74AC74 family. A voltage of 3V provides power to the D latch. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. A device of this type belongs to the family of AC. It is mounted in the way of Surface Mount. Basically, it is designed with a set of 14 pins. This device exhibits a clock edge trigger type of Positive Edge. This device is part of the FF/Latchesbase part number family. Vsup reaches 6V, the maximal supply voltage. Keeping the supply voltage (Vsup) above 2V is necessary for normal operation. To achieve this superior flexibility, 2 circuits are used. As a result of its reliability, this D flip flop is ideally suited for TR. A power supply of 3.3/5Vis required to operate it. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. It is designed with 1 output lines.
SN74AC74PWRG4 Features
Tape & Reel (TR) package
74AC series
14 pins
3.3/5V power supplies
SN74AC74PWRG4 Applications
There are a lot of Texas Instruments SN74AC74PWRG4 Flip Flops applications.
- Patented noise
- QML qualified product
- Counters
- Memory
- Registers
- Individual Asynchronous Resets
- Asynchronous counter
- Synchronous counter
- Data storage
- ESCC
