SN74ACT374DBR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 8.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 90000000Hz |
| Height | 2mm |
| Length | 7.2mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT374DBR Overview
It is packaged in the way of 20-SSOP (0.209, 5.30mm Width). D flip flop is embedded in the Cut Tape (CT) package. The output it is configured with uses Tri-State, Non-Inverted. It is configured with a trigger that uses Positive Edge. It is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. It is operating at -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. The 74ACTseries comprises this type of FPGA. A frequency of 160MHzshould not be exceeded by its output. A total of 1elements are contained within it. This process consumes 4μA quiescents. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. JK flip flop belongs to 74ACT374 family. The power supply voltage is 5V. Input capacitance of this device is 4.5pF farads. The electronic device belongs to the ACTfamily. Electronic part Surface Mountis mounted in the way. This board is designed with 20pins on it. This device's clock edge trigger type is Positive Edge. It is included in FF/Latches. There are 8bits in its design. Due to its superior flexibility, it uses 8 circuits. Considering the reliability of this T flip flop, it is well suited for TR. It operates from 5V power supplies. The flip flop has 2ports embedded within it. In order to achieve high efficiency, the supply voltage should be maintained at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. This input has 3lines.
SN74ACT374DBR Features
Cut Tape (CT) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT374DBR Applications
There are a lot of Texas Instruments SN74ACT374DBR Flip Flops applications.
- Frequency Dividers
- Modulo – n – counter
- Storage registers
- Bus hold
- Balanced 24 mA output drivers
- Reduced system switching noise
- Synchronous counter
- Latch-up performance
- Communications
- Computers
