SN74ACT374DW
| Parameters | |
|---|---|
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 10 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 8.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 8.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 90000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
SN74ACT374DW Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. There is an embedded version in the package Tube. In the configuration, Tri-State, Non-Invertedis used as the output. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. The supply voltage is set to 4.5V~5.5V. A temperature of -40°C~85°C TAis considered to be the operating temperature. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74ACT series. A frequency of 160MHzshould be the maximum output frequency. In total, it contains 1 elements. It has been determined that there have been 20 terminations. JK flip flop belongs to 74ACT374 family. It is powered from a supply voltage of 5V. Its input capacitance is 4.5pF farads. The electronic device belongs to the ACTfamily. There is an electronic part that is mounted in the way of Surface Mount. The 20pins are designed into the board. It has a clock edge trigger type of Positive Edge. The part is included in FF/Latches. 8bits are used in its design. The superior flexibility of this circuit is achieved by using 8 circuits. The D latch operates on 5V volts. A D flip flop with 2embedded ports is available. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. Its output current of 24mAallows for maximum design flexibility. A total of 3input lines have been provided. It consumes a total of 4μA quiescent current at any given time.
SN74ACT374DW Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT374DW Applications
There are a lot of Texas Instruments SN74ACT374DW Flip Flops applications.
- Asynchronous counter
- Latch
- Single Up Count-Control Line
- Safety Clamp
- Latch-up performance
- Data storage
- Single Down Count-Control Line
- Bounce elimination switch
- Communications
- Control circuits
