SN74ACT374PWR
| Parameters | |
|---|---|
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 90000000Hz |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74ACT374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 12.5 ns |
| Turn On Delay Time | 8.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
SN74ACT374PWR Overview
20-TSSOP (0.173, 4.40mm Width)is the way it is packaged. The Cut Tape (CT)package contains it. T flip flop uses Tri-State, Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. Surface Mountis positioned in the way of this electronic part. It operates with a supply voltage of 4.5V~5.5V. In this case, the operating temperature is -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. FPGAs belonging to the 74ACTseries contain this type of chip. You should not exceed 160MHzin the output frequency of the device. In total, it contains 1 elements. There is a consumption of 4μAof quiescent energy. There have been 20 terminations. Members of the 74ACT374family make up this object. The D flip flop is powered by a voltage of 5V . There is 4.5pF input capacitance for this T flip flop. An electronic device belonging to the family ACTcan be found here. In this case, the electronic component is mounted in the way of Surface Mount. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. This part is included in FF/Latches. The flip flop is designed with 8bits. The superior flexibility of this circuit is achieved by using 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TR. An electrical current of 5V volts is applied to it. There are 2 ports embedded in the flip flops. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. As a result of its output current of 24mA, it is very flexible in terms of design. Currently, there are 3 input lines present.
SN74ACT374PWR Features
Cut Tape (CT) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT374PWR Applications
There are a lot of Texas Instruments SN74ACT374PWR Flip Flops applications.
- EMI reduction circuitry
- ESD protection
- Digital electronics systems
- Latch-up performance
- Computers
- Communications
- Shift Registers
- Convert a momentary switch to a toggle switch
- Asynchronous counter
- Data storage
