SN74ACT533NSRE4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT533 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | Tri-State |
| Circuit | 8:8 |
| Polarity | Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Latch |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 24mA |
| Logic Type | D-Type Transparent Latch |
| Max I(ol) | 0.024 A |
| Independent Circuits | 1 |
| Number of Output Lines | 8 |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
SN74ACT533NSRE4 Overview
20-SOIC (0.209, 5.30mm Width) contains it. The package is in the form of Tape & Reel (TR). It uses Tri-State as the output. In this electrical device, the logic type is D-Type Transparent Latch. Mounting this electronic component follows the Surface Mount method. There is no supply voltage for this device. There is a temperature of -40°C~85°C at which the system operates. The 74ACT series contains FPGAs of this type. It is designed with 8 bits. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The family it belongs to is 74ACT533. The device works with a voltage of 5V for its supply voltage. It is equipped with 20 pin count. In the world of electronics, this electronic device belongs to the family of ACT. In addition, it is designed with a pin number of 20. Surface Mount is the method used for mounting this electronic part. This device has 2 ports that can be connected to it. The part is in the FF/Latches subcategory. There is a maximum voltage supply (Vsup) that reaches 5.5V. It operates from 5V power supplies. A voltage greater than 4.5V must be supplied as a power supply (Vsup). Considering the reliability of this device, it would be a good candidate for TAPE AND REEL. The binary equivalent of the input line is generated by 8 output lines.
SN74ACT533NSRE4 Features
20-SOIC (0.209, 5.30mm Width) package
74ACT series
8 Bits
74ACT533 family
20 pin count
20 pins
5V power supplies
SN74ACT533NSRE4 Applications
There are a lot of Texas Instruments SN74ACT533NSRE4 Latches applications.
- Double bus register system
- Phase comparator
- BCD counting
- Decade counting 7-segment decimal display
- Parallel data storage
- Motor Drives
- Parallel-to-Serial Data Conversion
- Automotive Cluster
- Relay replacement
- Flip-flops
