SN74ACT534DBR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 156.687814mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT534 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11.5 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2mm |
| Length | 7.2mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74ACT534DBR Overview
The package is in the form of 20-SSOP (0.209, 5.30mm Width). It is contained within the Cut Tape (CT)package. It is configured with Tri-State, Invertedas an output. This trigger is configured to use Positive Edge. Surface Mountis positioned in the way of this electronic part. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. A temperature of -40°C~85°C TAis considered to be the operating temperature. It belongs to the type D-Typeof flip flops. JK flip flop is a part of the 74ACTseries of FPGAs. You should not exceed 100MHzin the output frequency of the device. The element count is 1 . As a result, it consumes 4μA quiescent current. The number of terminations is 20. This D latch belongs to the family of 74ACT534. Power is supplied from a voltage of 5V volts. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the ACTfamily of D flip flop. There is an electronic part that is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. This device has the clock edge trigger type of Positive Edge. It is included in FF/Latches. It is designed with 8bits. The superior flexibility of this product is achieved by using 8 circuits. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. In order for the device to operate, it requires 5V power supplies. The flip flop has 2ports embedded within it. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. The 24mA output current allows it to be designed with the greatest amount of flexibility. This input has 3lines in it.
SN74ACT534DBR Features
Cut Tape (CT) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT534DBR Applications
There are a lot of Texas Instruments SN74ACT534DBR Flip Flops applications.
- Registers
- Data storage
- Digital electronics systems
- Instrumentation
- Clock pulse
- Convert a momentary switch to a toggle switch
- Bus hold
- Balanced 24 mA output drivers
- Single Down Count-Control Line
- CMOS Process
