SN74ACT534PWRG4
| Parameters | |
|---|---|
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT534 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11.5 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
SN74ACT534PWRG4 Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. The Tape & Reel (TR)package contains it. Tri-State, Invertedis the output configured for it. The trigger it is configured with uses Positive Edge. It is mounted in the way of Surface Mount. A supply voltage of 4.5V~5.5V is required for operation. In the operating environment, the temperature is -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. In terms of FPGAs, it belongs to the 74ACT series. You should not exceed 100MHzin the output frequency of the device. A total of 1elements are contained within it. There is a consumption of 4μAof quiescent energy. There have been 20 terminations. D latch belongs to the 74ACT534 family. A voltage of 5V is used to power it. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of ACT. A part of the electronic system is mounted in the way of Surface Mount. A total of 20pins are provided on this board. Its clock edge trigger type is Positive Edge. This RS flip flops is a part number FF/Latches. An electronic part designed with 8bits is used in this application. Its flexibility is enhanced by 8 circuits. Considering the reliability of this T flip flop, it is well suited for TR. There are 5V power supplies attached to it. There are 2 ports embedded in the flip flops. Optimal efficiency requires a supply voltage of 5V. With an output current of 24mA, it is possible to design the device in any way you want.
SN74ACT534PWRG4 Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT534PWRG4 Applications
There are a lot of Texas Instruments SN74ACT534PWRG4 Flip Flops applications.
- Supports Live Insertion
- Counters
- Registers
- Single Down Count-Control Line
- Buffer registers
- Bounce elimination switch
- Frequency Dividers
- Instrumentation
- Communications
- Computing
