SN74ACT564DWG4
| Parameters | |
|---|---|
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 6.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| Number of Bits per Element | 8 |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2.35mm |
| Length | 12.8mm |
| Width | 7.52mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Additional Feature | BROADSIDE VERSION OF 534 |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Frequency | 90MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
SN74ACT564DWG4 Overview
The flip flop is packaged in SOIC. In total, it contains 1 elements. There are 20 terminations,It is powered by a voltage of 5V . In this case, the D flip flop belongs to the ACTfamily. It is mounted by the way of Surface Mount. This board has 20 pins. It has a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. As a result of its reliability, this D flip flop is ideally suited for TUBE. It runs on 5Vvolts of power. There are 2 ports embedded in the flip flops. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. Additionally, there are BROADSIDE VERSION OF 534 on the electronic flip flop that can be referred to. A -24mAvalue is set for the high level output current. A 24mAvalue is set for low-level output current. There should be a temperature below 85°Cduring operation. A temperature above -40°Cshould be used for the operation. The minimal supply voltage is 4.5V. It supports a maximum supply voltage of 5.5V volts. It is possible to achieve a frequency of 90MHz. The logic IC it uses is BUS DRIVER. A total of 1 functions are provided by this T flip flop. It is equipped with 20 pin count. This flip flop features a maximum design flexibility due to its output current of 24mA.
SN74ACT564DWG4 Features
20 pins
5V power supplies
1 Functions
20 pin count
SN74ACT564DWG4 Applications
There are a lot of Texas Instruments SN74ACT564DWG4 Flip Flops applications.
- Reduced system switching noise
- Power down protection
- Latch
- Data transfer
- CMOS Process
- Frequency division
- Storage registers
- Registers
- Dynamic threshold performance
- Bus hold
