SN74ACT564NSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Weight | 266.712314mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT564 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 6.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 2mm |
| Length | 12.6mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT564NSR Overview
It is packaged in the way of 20-SOIC (0.209, 5.30mm Width). The package Tape & Reel (TR)contains it. In the configuration, Tri-State, Invertedis used as the output. This trigger uses the value Positive Edge. This electronic part is mounted in the way of Surface Mount. A 4.5V~5.5Vsupply voltage is required for it to operate. It is operating at a temperature of -40°C~85°C TA. The type of this D latch is D-Type. In this case, it is a type of FPGA belonging to the 74ACT series. It should not exceed 90MHzin terms of its output frequency. In total, it contains 1 elements. This process consumes 4μA quiescents. There are 20 terminations,This D latch belongs to the family of 74ACT564. The power supply voltage is 5V. There is 4.5pF input capacitance for this T flip flop. Electronic devices of this type belong to the ACTfamily. It is mounted by the way of Surface Mount. This board has 20 pins. This device has the clock edge trigger type of Positive Edge. This device has the base part number FF/Latches. 8bits are used in its design. 8 circuits are used to achieve its superior flexibility. In view of its reliability, this D flip flop is a good fit for TR. The system runs on a power supply of 5V watts. There are 2 ports embedded in the flip flops. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In addition to its maximum design flexibility, the output current of the T flip flop is 24mA. It is reported that there are 3 input lines.
SN74ACT564NSR Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT564NSR Applications
There are a lot of Texas Instruments SN74ACT564NSR Flip Flops applications.
- Reduced system switching noise
- Consumer
- Bus hold
- Instrumentation
- Matched Rise and Fall
- Functionally equivalent to the MC10/100EL29
- Pattern generators
- Safety Clamp
- Storage registers
- ESD performance
