SN74ACT564PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT564 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 24mA |
| Number of Bits | 8 |
| Clock Frequency | 90MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 6.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Translation | N/A |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT564PW Overview
In the form of 20-TSSOP (0.173, 4.40mm Width), it has been packaged. Package Tubeembeds it. The output it is configured with uses Tri-State, Inverted. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at 4.5V~5.5Vvolts. It is at -40°C~85°C TAdegrees Celsius that the system is operating. This D latch has the type D-Type. This type of FPGA is a part of the 74ACT series. You should not exceed 90MHzin the output frequency of the device. In total, it contains 1 elements. It consumes 4μA of quiescent current without being affected by external factors. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is a member of the 74ACT564 family. The D flip flop is powered by a voltage of 5V . Its input capacitance is 4.5pFfarads. ACTis the family of this D flip flop. In this case, the electronic component is mounted in the way of Surface Mount. This board is designed with 20pins on it. In this device, the clock edge trigger type is Positive Edge. This device is part of the FF/Latchesbase part number family. There are 8bits in its design. Using 8 circuits, it is highly flexible. A total of 5V power supplies are needed to run it. This flip flop has a total of 2ports. High efficiency requires the supply voltage to be maintained at 5V. The 24mA output current allows it to be designed with the greatest amount of flexibility. This input has 3lines in it.
SN74ACT564PW Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
SN74ACT564PW Applications
There are a lot of Texas Instruments SN74ACT564PW Flip Flops applications.
- Buffer registers
- Asynchronous counter
- Common Clocks
- Individual Asynchronous Resets
- Load Control
- Safety Clamp
- Frequency division
- ESD protection
- Synchronous counter
- Clock pulse
