SN74ACT574PWRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Frequency | 110MHz |
| Pin Count | 20 |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Circuits | 8 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 24mA |
| Number of Bits | 8 |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 7 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | BUS DRIVER |
| Max I(ol) | 0.024 A |
| High Level Output Current | -24mA |
| Low Level Output Current | 24mA |
| Number of Input Lines | 3 |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.15mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74ACT574PWRG4 Overview
As a result, it is packaged as TSSOP. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is powered from a supply voltage of 5V. Electronic devices of this type belong to the ACTfamily. There is an electronic part that is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. This device has Positive Edgeas its clock edge trigger type. There is a base part number FF/Latchesfor the RS flip flops. It is designed with a number of bits of 8. The superior flexibility of this product is achieved by using 8 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. It operates from 5V power supplies. The flip flop has 2embedded ports. For high efficiency, the supply voltage should be kept at 5V. In order to operate, the chip has 1 output lines. Currently, there are 3 input lines present. High level output current is set to -24mA. A 24mAvalue is set for low-level output current. Ideally, the operating temperature should be below 85°C. Ideally, the operating temperature should be greater than -40°C. The system operates with a minimum supply voltage of 4.5V. A maximum voltage of 5.5V can be provided by it. It is possible to obtain a frequency of 110MHz. In this case, it uses a BUS DRIVER logic IC. A total of 1 functions are available on the T flip flop. It has 20 pins. In addition to its maximum design flexibility, the output current of the flip flop is 24mA.
SN74ACT574PWRG4 Features
20 pins
8 Bits
5V power supplies
1 Functions
20 pin count
SN74ACT574PWRG4 Applications
There are a lot of Texas Instruments SN74ACT574PWRG4 Flip Flops applications.
- Clock pulse
- Asynchronous counter
- Counters
- Balanced Propagation Delays
- Digital electronics systems
- Individual Asynchronous Resets
- Consumer
- Dynamic threshold performance
- Latch
- Frequency Divider circuits
