SN74ACT74DG4
| Parameters | |
|---|---|
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 210MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 5.5 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 129.387224mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
SN74ACT74DG4 Overview
In the form of 14-SOIC (0.154, 3.90mm Width), it has been packaged. Package Tubeembeds it. As configured, the output uses Differential. There is a trigger configured with Positive Edge. Surface Mountis occupied by this electronic component. A voltage of 4.5V~5.5Vis required for its operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. JK flip flop belongs to the 74ACTseries of FPGAs. A frequency of 210MHzshould not be exceeded by its output. This process consumes 2μA quiescents. There are 14 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. Members of the 74ACT74family make up this object. It is powered by a voltage of 5V . The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. It is a member of the ACTfamily of D flip flop. Surface Mount mounts this electronic component. Basically, it is designed with a set of 14 pins. This device exhibits a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. Its flexibility is enhanced by 2 circuits. A total of 5V power supplies are needed to run it. For high efficiency, the supply voltage should be set to 5V. This T flip flop features a maximum design flexibility due to its output current of 24mA. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
SN74ACT74DG4 Features
Tube package
74ACT series
14 pins
5V power supplies
SN74ACT74DG4 Applications
There are a lot of Texas Instruments SN74ACT74DG4 Flip Flops applications.
- Latch-up performance
- EMI reduction circuitry
- Automotive
- Reduced system switching noise
- Memory
- Patented noise
- Frequency Dividers
- Functionally equivalent to the MC10/100EL29
- Load Control
- Event Detectors
