SN74ACT74NSR
| Parameters | |
|---|---|
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 208.312296mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 210MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 5.5 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
SN74ACT74NSR Overview
14-SOIC (0.209, 5.30mm Width)is the way it is packaged. The package Cut Tape (CT)contains it. As configured, the output uses Differential. It is configured with the trigger Positive Edge. Surface Mountis occupied by this electronic component. The JK flip flop operates at a voltage of 4.5V~5.5V. -40°C~85°C TAis the operating temperature. The type of this D latch is D-Type. FPGAs belonging to the 74ACTseries contain this type of chip. It should not exceed 210MHzin its output frequency. Despite external influences, it consumes 2μAof quiescent current. 14terminations have occurred. The 74ACT74 family contains it. A voltage of 5V provides power to the D latch. Input capacitance of this device is 3pF farads. ACTis the family of this D flip flop. Electronic part Surface Mountis mounted in the way. Basically, it is designed with a set of 14 pins. It has a clock edge trigger type of Positive Edge. It is included in FF/Latches. Due to its superior flexibility, it uses 2 circuits. In light of its reliable performance, this T flip flop is well suited for TR. An electrical current of 5V volts is applied to it. In order to ensure high efficiency, the supply voltage should remain at 5V. With a current output of 24mA , it offers maximum design flexibility. This input has 4lines in it.
SN74ACT74NSR Features
Cut Tape (CT) package
74ACT series
14 pins
5V power supplies
SN74ACT74NSR Applications
There are a lot of Texas Instruments SN74ACT74NSR Flip Flops applications.
- Latch
- Data Synchronizers
- Modulo – n – counter
- Convert a momentary switch to a toggle switch
- Storage Registers
- Bus hold
- Single Down Count-Control Line
- Reduced system switching noise
- QML qualified product
- Buffered Clock
