SN74ACT74PW
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 210MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 5.5 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT74PW Overview
The item is packaged in 14-TSSOP (0.173, 4.40mm Width)cases. Package Tubeembeds it. As configured, the output uses Differential. It is configured with a trigger that uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. The operating temperature is -40°C~85°C TA. A flip flop of this type is classified as a D-Type. It belongs to the 74ACTseries of FPGAs. It should not exceed 210MHzin terms of its output frequency. It consumes 2μA of quiescent There are 14 terminations,D latch belongs to the 74ACT74 family. A voltage of 5V is used as the power supply for this D latch. A 3pFfarad input capacitance is provided by this T flip flop. A device of this type belongs to the family of ACT. There is an electronic component mounted in the way of Surface Mount. The 14pins are designed into the board. In this device, the clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The superior flexibility of this product is achieved by using 2 circuits. There are 5V power supplies attached to it. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. Its output current of 24mAallows for maximum design flexibility. This input has 4lines in it.
SN74ACT74PW Features
Tube package
74ACT series
14 pins
5V power supplies
SN74ACT74PW Applications
There are a lot of Texas Instruments SN74ACT74PW Flip Flops applications.
- Memory
- Guaranteed simultaneous switching noise level
- Data transfer
- Buffer registers
- Latch-up performance
- Test & Measurement
- ESCC
- Frequency division
- Parallel data storage
- Load Control
