SN74ACT74PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Output Current | 24mA |
| Clock Frequency | 210MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 5.5 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 2μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 3pF |
| Number of Input Lines | 4 |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74ACT74PWR Overview
The package is in the form of 14-TSSOP (0.173, 4.40mm Width). A package named Cut Tape (CT)includes it. Currently, the output is configured to use Differential. In the configuration of the trigger, Positive Edgeis used. Surface Mountis occupied by this electronic component. A supply voltage of 4.5V~5.5V is required for operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. A flip flop of this type is classified as a D-Type. In FPGA terms, D flip flop is a type of 74ACTseries FPGA. It should not exceed 210MHzin its output frequency. It consumes 2μA of quiescent The number of terminations is 14. If you search by 74ACT74, you will find similar parts. A voltage of 5V provides power to the D latch. The input capacitance of this T flip flop is 3pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. In terms of electronic devices, this device belongs to the ACTfamily of devices. This electronic part is mounted in the way of Surface Mount. The electronic flip flop is designed with pins 14. This device's clock edge trigger type is Positive Edge. It is included in FF/Latches. Its superior flexibility is attributed to its use of 2 circuits. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TR. It runs on 5Vvolts of power. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. Featuring the maximum design flexibility, it has an output current of 24mA . This input has 4lines in it.
SN74ACT74PWR Features
Cut Tape (CT) package
74ACT series
14 pins
5V power supplies
SN74ACT74PWR Applications
There are a lot of Texas Instruments SN74ACT74PWR Flip Flops applications.
- Count Modes
- Storage registers
- Differential Individual
- Control circuits
- Data storage
- Asynchronous counter
- Balanced Propagation Delays
- Power down protection
- Pattern generators
- ESD protection
