SN74AHC174D
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 141.690917mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AHC174 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Clock Frequency | 180MHz |
| Propagation Delay | 14.5 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Number of Bits per Element | 6 |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.7pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 80000000Hz |
| Height | 1.75mm |
| Length | 9.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC174D Overview
The package is in the form of 16-SOIC (0.154, 3.90mm Width). The package Tubecontains it. T flip flop uses Non-Invertedas the output. It is configured with a trigger that uses Positive Edge. Surface Mountmounts this electrical part. The supply voltage is set to 2V~5.5V. It is at -40°C~85°C TAdegrees Celsius that the system is operating. It belongs to the type D-Typeof flip flops. JK flip flop belongs to the 74AHCseries of FPGAs. You should not exceed 180MHzin the output frequency of the device. In total, it contains 1 elements. It consumes 4μA of quiescent current without being affected by external factors. There are 16 terminations,You can search similar parts based on 74AHC174. The power source is powered by 3.3V. The input capacitance of this T flip flop is 1.7pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the AHC/VHC/H/U/Vfamily are electronic devices. The electronic part is mounted in the way of Surface Mount. As you can see from the design, it has pins with 16. It has a clock edge trigger type of Positive Edge. The part is included in FF/Latches. There is a 5.5Vmaximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be above 2V. Despite its superior flexibility, it relies on 7 circuits to achieve it. It runs on 2/5.5Vvolts of power. With an output current of 8mA, it is possible to design the device in any way you want. This input has 3lines.
SN74AHC174D Features
Tube package
74AHC series
16 pins
2/5.5V power supplies
SN74AHC174D Applications
There are a lot of Texas Instruments SN74AHC174D Flip Flops applications.
- Frequency Divider circuits
- Individual Asynchronous Resets
- Latch-up performance
- Consumer
- Balanced Propagation Delays
- ESD protection
- Bounce elimination switch
- ATE
- Functionally equivalent to the MC10/100EL29
- Buffered Clock
