SN74AHC174NSRG4
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHC174 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Number of Bits | 6 |
| Clock Frequency | 180MHz |
| Propagation Delay | 14.5 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Max I(ol) | 0.008 A |
| Max Propagation Delay @ V, Max CL | 9.2ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 1.7pF |
| Number of Output Lines | 6 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 80000000Hz |
| Height Seated (Max) | 2mm |
| Width | 5.3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Weight | 200.686274mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHC |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 3.3V |
SN74AHC174NSRG4 Overview
In the form of 16-SOIC (0.209, 5.30mm Width), it has been packaged. D flip flop is included in the Tape & Reel (TR)package. Non-Invertedis the output configured for it. It is configured with a trigger that uses Positive Edge. Surface Mountmounts this electrical part. With a supply voltage of 2V~5.5V volts, it operates. It is at -40°C~85°C TAdegrees Celsius that the system is operating. The type of this D latch is D-Type. It belongs to the 74AHCseries of FPGAs. Its output frequency should not exceed 180MHz. In total, there are 1 elements. It consumes 4μA of quiescent current without being affected by external factors. There have been 16 terminations. This D latch belongs to the family of 74AHC174. An input voltage of 3.3Vpowers the D latch. The input capacitance of this T flip flop is 1.7pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. This D flip flop belongs to the family of AHC/VHC/H/U/V. Electronic part Surface Mountis mounted in the way. 16pins are included in its design. A Positive Edgeclock edge trigger is used in this device. It is included in FF/Latches. There are 6bits in its design. Vsup reaches its maximum value at 5.5V. Normally, the supply voltage (Vsup) should be kept above 2V. The superior flexibility of this product is achieved by using 7 circuits. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. The D latch runs on a voltage of 2/5.5V volts. With an output current of 8mA, this device offers maximum design flexibility. There are 6 output lines on it.
SN74AHC174NSRG4 Features
Tape & Reel (TR) package
74AHC series
16 pins
6 Bits
2/5.5V power supplies
SN74AHC174NSRG4 Applications
There are a lot of Texas Instruments SN74AHC174NSRG4 Flip Flops applications.
- Matched Rise and Fall
- Guaranteed simultaneous switching noise level
- Test & Measurement
- Frequency Divider circuits
- Registers
- Differential Individual
- Frequency division
- Computing
- Asynchronous counter
- Bounce elimination switch
