SN74AHC273DW
| Parameters | |
|---|---|
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 17.1 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height | 2.65mm |
| Length | 12.8mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Weight | 500.709277mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
SN74AHC273DW Overview
As a result, it is packaged as 20-SOIC (0.295, 7.50mm Width). You can find it in the Tubepackage. In the configuration, Non-Invertedis used as the output. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~5.5V. Currently, the operating temperature is -40°C~125°C TA. A flip flop of this type is classified as a D-Type. FPGAs belonging to the 74AHCseries contain this type of chip. Its output frequency should not exceed 110MHz Hz. In total, there are 1 elements. This process consumes 4μA quiescents. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. JK flip flop belongs to 74AHC273 family. An input voltage of 3.3Vpowers the D latch. This JK flip flop has a 2.5pFfarad input capacitance. The electronic device belongs to the AHC/VHC/H/U/Vfamily. A part of the electronic system is mounted in the way of Surface Mount. This board has 20 pins. This device has the clock edge trigger type of Positive Edge. It is included in FF/Latches. The design is based on 8bits. Vsup reaches its maximum value at 5.5V. The supply voltage (Vsup) should be kept above 2V for normal operation. Due to its superior flexibility, it uses 8 circuits. It operates from 2/5.5V power supplies. With a current output of 8mA , it offers maximum design flexibility. Currently, there are 3 input lines present.
SN74AHC273DW Features
Tube package
74AHC series
20 pins
8 Bits
2/5.5V power supplies
SN74AHC273DW Applications
There are a lot of Texas Instruments SN74AHC273DW Flip Flops applications.
- Load Control
- Event Detectors
- Memory
- Buffer registers
- Bounce elimination switch
- EMI reduction circuitry
- 2 – Bit synchronous counter
- Bus hold
- Registers
- Test & Measurement
