SN74AHC273PWG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TUBE |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 110MHz |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Current - Output | 8mA |
| Propagation Delay | 17.1 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Logic IC Type | D FLIP-FLOP |
| Number of Bits per Element | 8 |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AHC273PWG4 Overview
In the form of TSSOP, it has been packaged. A total of 1 elements are present. 20terminations have occurred. A voltage of 3.3V provides power to the D latch. It is a member of the AHC/VHC/H/U/Vfamily of D flip flop. Surface Mount mounts this electronic component. This board has 20 pins. In this device, the clock edge trigger type is Positive Edge. It is included in FF/Latches. Considering the reliability of this T flip flop, it is well suited for TUBE. A -8mAis set for the high level output current. It is set to 8mAfor low level output current. If the operating temperature is lower than 125°C, it is recommended. In order for the system to operate properly, the temperature should be higher than -40°C. The system operates with a minimum supply voltage of 2V. 5.5Vis the maximum supply voltage supported by it. It is possible to achieve a frequency of 110MHz. There is a logic IC D FLIP-FLOP used in the D flip flop. It is equipped with 1 Functions . The D latch is equipped with 20 pins. As a result of the output current of 8mA, the design flexibility is maximized.
SN74AHC273PWG4 Features
20 pins
1 Functions
20 pin count
SN74AHC273PWG4 Applications
There are a lot of Texas Instruments SN74AHC273PWG4 Flip Flops applications.
- ESD performance
- Frequency division
- Latch
- Single Up Count-Control Line
- Data Synchronizers
- Functionally equivalent to the MC10/100EL29
- Common Clocks
- Supports Live Insertion
- Storage registers
- Shift Registers
