SN74AHC273PWR
| Parameters | |
|---|---|
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Lifecycle Status | ACTIVE (Last Updated: 1 day ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Cut Tape (CT) |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | 74AHC273 |
| Function | Master Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 110MHz |
| Propagation Delay | 17.1 ns |
| Quiescent Current | 4μA |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 2.5pF |
| Power Supply Current-Max (ICC) | 0.04mA |
| Number of Input Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 70000000Hz |
| Height | 1.2mm |
SN74AHC273PWR Overview
It is embeded in 20-TSSOP (0.173, 4.40mm Width) case. A package named Cut Tape (CT)includes it. T flip flop uses Non-Invertedas its output configuration. JK flip flop uses Positive Edgeas the trigger. This electronic part is mounted in the way of Surface Mount. A 2V~5.5Vsupply voltage is required for it to operate. In this case, the operating temperature is -40°C~125°C TA. D-Typeis the type of this D latch. It is a type of FPGA belonging to the 74AHC series. It should not exceed 110MHzin its output frequency. A total of 1elements are present in it. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. You can search similar parts based on 74AHC273. Power is provided by a 3.3V supply. The input capacitance of this T flip flop is 2.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the AHC/VHC/H/U/Vfamily. The electronic part is mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device exhibits a clock edge trigger type of Positive Edge. This part is included in FF/Latches. This flip flop is designed with 8 Bits. As soon as Vsup reaches 5.5V, the maximum supply voltage is reached. It is imperative that the supply voltage (Vsup) is maintained above 2Vin order to ensure normal operation. Its superior flexibility is attributed to its use of 8 circuits. Due to its reliability, this T flip flop is well suited for TR. An electrical current of 2/5.5V volts is applied to it. It offers maximum design flexibility with its output current of 8mA. This input has 3lines. Quiescent current is consumed by the D latch in the amount of 4μA.
SN74AHC273PWR Features
Cut Tape (CT) package
74AHC series
20 pins
8 Bits
2/5.5V power supplies
SN74AHC273PWR Applications
There are a lot of Texas Instruments SN74AHC273PWR Flip Flops applications.
- Safety Clamp
- Circuit Design
- Functionally equivalent to the MC10/100EL29
- EMI reduction circuitry
- Data transfer
- ESCC
- Single Down Count-Control Line
- Memory
- Computers
- Registers
