SN74AHC374DGVRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TFSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Weight | 60.186038mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Series | 74AHC |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Voltage - Supply | 2V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.4mm |
| Base Part Number | 74AHC374 |
| Function | Standard |
| Output Type | Tri-State, Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 2/5.5V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Output Current | 8mA |
| Number of Bits | 8 |
| Clock Frequency | 120MHz |
| Propagation Delay | 16.2 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Output Characteristics | 3-STATE |
| Current - Output High, Low | 8mA 8mA |
| Max Propagation Delay @ V, Max CL | 10.1ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4pF |
| Number of Input Lines | 8 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
SN74AHC374DGVRG4 Overview
The flip flop is packaged in 20-TFSOP (0.173, 4.40mm Width). It is contained within the Tape & Reel (TR)package. As configured, the output uses Tri-State, Non-Inverted. This trigger is configured to use Positive Edge. It is mounted in the way of Surface Mount. The supply voltage is set to 2V~5.5V. It is at -40°C~85°C TAdegrees Celsius that the system is operating. It belongs to the type D-Typeof flip flops. FPGAs belonging to the 74AHCseries contain this type of chip. Its output frequency should not exceed 120MHz. In total, it contains 1 elements. As a result, it consumes 4μA quiescent current. A total of 20 terminations have been made. The 74AHC374 family contains it. Power is supplied from a voltage of 3.3V volts. The input capacitance of this T flip flop is 4pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the AHC/VHC/H/U/Vfamily are electronic devices. There is an electronic component mounted in the way of Surface Mount. The 20pins are designed into the board. In this device, the clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The design is based on 8bits. The maximal supply voltage (Vsup) reaches 5.5V. Normal operation requires a supply voltage (Vsup) above 2V. As a result of its reliability, this D flip flop is ideally suited for TR. The system runs on a power supply of 2/5.5V watts. There are 2 ports embedded in the flip flops. It offers maximum design flexibility with its output current of 8mA. Currently, there are 8 lines of input.
SN74AHC374DGVRG4 Features
Tape & Reel (TR) package
74AHC series
20 pins
8 Bits
2/5.5V power supplies
SN74AHC374DGVRG4 Applications
There are a lot of Texas Instruments SN74AHC374DGVRG4 Flip Flops applications.
- Frequency Dividers
- Bounce elimination switch
- Bus hold
- Computing
- Set-reset capability
- Power down protection
- Dynamic threshold performance
- Memory
- Single Down Count-Control Line
- CMOS Process
