SN74AHC374PWRG4
| Parameters | |
|---|---|
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Package / Case | TSSOP |
| Number of Pins | 20 |
| Weight | 76.997305mg |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 20 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 125°C |
| Min Operating Temperature | -40°C |
| Subcategory | FF/Latches |
| Packing Method | TR |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 120MHz |
| Pin Count | 20 |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Current - Output | 8mA |
| Propagation Delay | 16.2 ns |
| Turn On Delay Time | 1 ns |
| Family | AHC/VHC/H/U/V |
| Logic Function | D-Type, Flip-Flop |
| Output Characteristics | 3-STATE |
| Logic IC Type | BUS DRIVER |
| Number of Bits per Element | 8 |
| High Level Output Current | -8mA |
| Low Level Output Current | 8mA |
| Control Type | ENABLE LOW |
| Power Supply Current-Max (ICC) | 0.04mA |
| Count Direction | UNIDIRECTIONAL |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.2mm |
| Length | 6.5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
SN74AHC374PWRG4 Overview
TSSOPis the packaging method. D latch consists of 1 elements. There are 20 terminations,The power supply voltage is 3.3V. This D flip flop belongs to the family of AHC/VHC/H/U/V. It is mounted in the way of Surface Mount. With its 20pins, it is designed to work with most electronic flip flops. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The RS flip flops belongs to FF/Latches base part number. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TR. This D flip flop is equipped with 0 ports. It is set to -8mAfor the high level output current. Low level output current is set to 8mA. A temperature below 125°Cis recommended for operation. The operating temperature should be higher than -40°C. The RS flip flop is designed to operate with a minimal supply voltage of 2VV. The maximum supply voltage supported by the flip flop is 5.5V. We are able to achieve a frequency of 120MHz. BUS DRIVERis used as the logic IC in this D flip flop. There are 1 functions available on the JK flip flop. The D latch is equipped with 20 pins. It features maximum design flexibility due to the 8mA output current.
SN74AHC374PWRG4 Features
20 pins
1 Functions
20 pin count
SN74AHC374PWRG4 Applications
There are a lot of Texas Instruments SN74AHC374PWRG4 Flip Flops applications.
- Test & Measurement
- Digital electronics systems
- ATE
- Storage registers
- Data Synchronizers
- Bus hold
- Computers
- Patented noise
- Parallel data storage
- Storage Registers
