Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
14-DIP (0.300, 7.62mm) |
Number of Pins |
14 |
Weight |
925.810377mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
Not Applicable |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
4 |
Supply Voltage |
2.3V |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
74AHC4066 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Max Supply Current |
20μA |
Throw Configuration |
SPST |
Propagation Delay |
4 ns |
Turn On Delay Time |
10 ns |
Supply Type |
Single |
Bandwidth |
50MHz |
Turn-Off Delay Time |
16 ns |
On-State Resistance (Max) |
75Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
40 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
0.5pF 5.5pF |
On-state Resistance Match-Nom |
6Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
12ns, 12ns |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-45dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
25ns |
Switch-off Time-Max |
25ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Normal Position |
NO |
Height |
5.08mm |
Length |
19.3mm |
Width |
6.35mm |
Thickness |
3.9mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
SN74AHC4066N Overview
Shipping overseas is convenient due to the electrical component's packing in 14-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. A switch device like this is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. 14 terminations have been made so far. A electrical component with 4 channels is capable of high-quality output. If the voltage supply is 2.3V volts, the electrical component should be turned on and run. An injection of 14 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPST - NO switching circuits. 74AHC4066 can be used to search for analog multiplexer variants. There is 75Ohm internal resistance in this digital multiplexer. To find out what the 14 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. Analogue multiplexers of the Single supply type that are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. Putting voltage greater than 20μA on the multiplexer may cause damage. There are SEPARATE OUTPUT outputs on this analog switch ic. A 50MHz-bandwidth can be used for data transfer.
SN74AHC4066N Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 50MHz
SN74AHC4066N Applications
There are a lot of Texas Instruments SN74AHC4066N Analog Switches & Multiplexers ICs applications.
- ATM
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Audio/video switches
- Audio and video signal routing
- Digital cross connects (DSX-1)
- DSLAMs
- Microprocessor Controlled Analog Systems
- Mechanical reed relay replacement
- DSUs
- Intelligent PBX