SN74AHC4066NSR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Weight | 208.312296mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 75Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.3V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 75Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 5.5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 12ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -45dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 2mm |
| Length | 10.3mm |
| Width | 5.3mm |
| Thickness | 1.95mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC4066NSR Overview
Shipping overseas is convenient with the electronic component packed in 14-SOIC (0.209, 5.30mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Temperatures around -40°C~85°C TA are extended for operation. The total number of terminations is 14. The electronic part provides high-quality output because it has 4 channels. When the electronic component is given a voltage of 2.3V, it should be turned on and run. It is part of the design of the 14 series that this electronic component is included. Unlike digital switches, these are based on SPST - NO switching circuits. If you are looking for variants of the digital switch, trying search with 74AHC4066. As far as internal resistance is concerned, it has 75Ohm. To find out what the functions of 14 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 5.5V voltage to the switch device. A analog switch ic that has a cost-effective Single supply type. A low voltage of 2V should be applied to the electronic component. A voltage of 2V~5.5V is required for this switch device, which drains from a single voltage source. A voltage higher than 20μA may cause damage to the switch multiplexer. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. The data can be transferred over a wide range of bandwidths, called 50MHz bandwidths.
SN74AHC4066NSR Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 50MHz
SN74AHC4066NSR Applications
There are a lot of Texas Instruments SN74AHC4066NSR Analog Switches & Multiplexers ICs applications.
- Imaging
- Mechanical reed relay replacement
- Switching Systems
- Video signal routing
- Isolation
- MP3 players
- Avionics
- Intelligent PBX
- Data Acquisition Systems
- High reliability control systems
