SN74AHC4066PW
| Parameters | |
|---|---|
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 12 ns |
| On-State Resistance (Max) | 75Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 5.5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 12ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -45dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 25ns |
| Switch-off Time-Max | 25ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Resistance | 75Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AHC4066 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
SN74AHC4066PW Overview
Presented in 14-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tube is used. In Surface Mount, you'll find this switch device. 1:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. A total of 14 terminations have been recorded. A electrical component with 4 channels is capable of high-quality output. In the case of a voltage supply of 2.3V volts, the electrical part can be powered up and run. A total of 14 pins are injected into the body of the electronic part. A SPST - NO switching circuit is used for these analog switches. Try searching for the analog switch ic with 74AHC4066 if you are looking for variants. In this multiplexer, the internal resistance is 75Ohm. For details about the functions of 14 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. It is recommended to use 2V as the lowest voltage for the electrical part. An analogue multiplexer drains from a single voltage supply at 2V~5.5V. Putting voltage greater than 20μA on the multiplexer may cause damage. There are 50MHz bandwidths for data transfer.
SN74AHC4066PW Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 50MHz
SN74AHC4066PW Applications
There are a lot of Texas Instruments SN74AHC4066PW Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- Precision test equipment
- Frame Relay Equipment
- Industrial and process control systems
- Digital cross connects (DSX-1)
- Avionics test equipment
- Cellular phones
- Fiber In The Loop (FITL)
- Microprocessor Controlled Analog Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
