SN74AHC4066PWR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 57.209338mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 75Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.3V |
| Base Part Number | 74AHC4066 |
| Output | SEPARATE OUTPUT |
| Pin Count | 14 |
| Polarity | Non-Inverting |
| Power Supplies | 2.5/5V |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Nominal Supply Current | 20μA |
| Max Supply Current | 20μA |
| Throw Configuration | SPST |
| Propagation Delay | 4 ns |
| Turn On Delay Time | 25 ns |
| Supply Type | Single |
| Bandwidth | 50MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 75Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 40 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 0.5pF 5.5pF |
| On-state Resistance Match-Nom | 6Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 12ns |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -45dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1.2mm |
| Length | 5mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
SN74AHC4066PWR Overview
The electronic component is convenient to ship overseas because it is packed in a 14-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Cut Tape (CT). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 14. This electronic part offers high-quality output due to its 4 channels. An 2.3V voltage supply should allow the electrical part to be turned on and run. An electrical component like this is included in the 14 series. A SPST - NO switching circuit is used for these analog switches. Search with 74AHC4066 if you are looking for analog multiplexer variants. Analog switches have 75Ohm internal resistance. The datasheets for the 14 pins explain the functions. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 5.5V. Analog switch ics with Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 2V. The voltage required by this switch device is 2V~5.5V, draining from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 20μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. 50MHz-bandwidths can be used to transfer data between multiplexers.
SN74AHC4066PWR Features
4 Channels
Switch Circuit: SPST - NO
Bandwidth: 50MHz
SN74AHC4066PWR Applications
There are a lot of Texas Instruments SN74AHC4066PWR Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- Fiber In The Loop (FITL)
- Optical Applications
- High-Voltage
- Sample-and-hold systems
- Wireless Local Loop
- High speed data transmission line cards
- RGB switches
- Medical systems
- Digital access cross connects
